The Toyota Sequoia has a recommended pressure of 30 to 33 pounds per square inch (psi) for the front tires and 33 psi for the rear tires.
Keeping your tires at the correct pressure is vital when it comes to road safety. Improperly inflated tires can lead to poor fuel efficiency and unstable steering as your vehicle becomes more difficult to handle. The worst-case scenario? Overly inflated tires have a higher risk of blowing out, which is extremely dangerous when you’re driving!
In this article, car insurance
super app Jerry
will walk you through the suggested tire pressure for the Toyota Sequoia. We’ll also teach you how to check your tire pressure manually and reset the dashboard warning light. Stay until the end for some helpful tips on lowering Toyota car insurance costs
! What is the right tire pressure for a Toyota Sequoia?
The Toyota Sequoia eight-seat SUV has a recommended tire pressure of 30 to 33 psi for the front tires and 33 psi for the rear tires. You can confirm the exact value for your model in your owner’s manual. You can also find this information on the sticker inside the driver-side door frame.
However, if you have winter tires on for the cold season, you may need to increase the tire pressure by 3 to 5 psi for the front and rear tires.
Tire pressure recommendations for other Toyota vehicles
4.717k Ratings5M+Drivers Joined
7M+Cars Garaged
Models with a range of tire pressures will have a specific combination for the front and rear tires depending on the tire size. Be sure to check the owner’s manual or the walls of the tires themselves to confirm the exact pressure for specific tires.
MORE: How low can your tire pressure go?
How to check Toyota Sequoia tire pressure
When the tires have too much or too little air, there will be a noticeable decline in ride quality and fuel efficiency. Thankfully, the monitoring system on the Sequoia will let you know if the pressure needs to be adjusted. If the tires need more air, the tire pressure light will light up on the dashboard.
On the other hand, there’s no need to fret if your tire pressure light isn’t working. You can still manually check the tire pressure with a few simple steps. Here’s how:
Remove the valve stem cap on all four tires
The reading on the gauge reflects the current tire pressure. To adjust the tire pressure back to the recommended values, you can add or remove air. This process can be done at a gas station (with an air-filling station) or even at home if you have an air compressor.
Vehicles with tires that are inflated improperly tend to be harder to handle. If you find yourself having difficulties steering your car, this may be an indication that the tires aren’t at the correct pressure.
How often should you check tire pressure?
A good habit would be to do a monthly tire pressure check to ensure all the tires are inflated correctly—and don’t forget the spare if you have one! It is also good practice to check tire pressure before any long trips to avoid car troubles on the road.
How to tell if your Toyota Sequoia needs new tires
On average, tires on the Toyota Sequoia, and any other car, should be replaced every six years. However, the actual life expectancy will depend on how much you drive. While you check the tire pressure, spare some time to inspect your tires’ condition as well. Get new tires as soon as possible if there’s low tread depth or cracks and bulges.
A handy trick to measure the tread depth when you don’t have a ruler is to use the penny method. Just put a penny into the tire tread, Lincoln’s head first. If you can see the top of his head, the tread is too worn and you need new tires!
How to reset the Toyota Sequoia tire pressure monitoring system (TPMS) light
Some Toyota Sequoia owners have reported that the TPMS warning light doesn’t turn off, even after adjusting the air pressure in their tires. You may need to reset the tire pressure light
to fix the malfunction. The Toyota Sequoia uses a direct tire pressure monitoring system, where sensors are installed inside the wheel. It uses tire pressure warning valves and transmitters to detect low tire pressure so a recalibration may be needed from time to time. Just follow the steps below.
First, you will need to find the TPMS reset button to initialize the tire pressure warning system. Your owner’s manual will give more detailed instructions specific to your model, but here’s a general gist of what needs to be done:
Park the Sequoia and turn the engine off
Adjust the pressure to the cold tire inflation pressure level specified
Turn the engine switch to “on”
Push and hold the TPMS reset button until the light blinks three times and “- -” is displayed
Start the car and drive at approximately 25 mph for 10 to 50 minutes to reset the sensor
These steps should turn off the TPMS warning light. However, if the lights start to blink again within 60 seconds, continue to drive for another 20 minutes.
If these steps don’t resolve the issue, bring your Sequoia to your local Toyota dealership service center or an independent mechanic to diagnose the problem.
How to save on Toyota Sequoia insurance
Driving with the correct tire pressure will keep your tires in good condition longer and help save on maintenance costs. Making a habit of checking your tire pressure will also help save on gas, as your car will drive more efficiently.
If you want to kick your savings up another notch, use the Jerry
app to reduce your Toyota Sequoia insurance costs
! As a trustworthy insurance comparison tool
, Jerry can find you competitive quotes from name-brand insurers in seconds. If you see a policy you want, Jerry’s team of licensed agents will handle all the paperwork and phone calls to get you switched over. “Jerry
was quick, simple, and saved me a headache searching for the best policy on my brand-new car. I definitely like this service!” —Rich N.
RECOMMENDEDInstantly compare top insurance companies
No spam or unwanted phone calls · No long forms
What insurance do you want to compare?
We value your privacy
