Including the hybrid version, the 2010 Honda Civic was available with four different engines. The oil capacity varies slightly depending on the engine.

In general, you’ll need somewhere between 3.2 to 4.6 quarts of oil for a 2010 Honda Civic. The exact amount will depend on your specific model’s engine. If you’re not sure which model you have, check your owner’s manual or look for a stamp on your engine block.

It’s a good idea to read related sections of your owner’s manual before performing any maintenance. Most manuals are available online if you’ve misplaced the physical copy.

But for now, allow

Jerry

—the

car insurance

app that saves you money on

Honda Civic insurance costs

—to walk you through the oil capacity of a 2010 Honda Civic, engine by engine.

Jerry sends free alerts to keep your car up-to-date so you can avoid costly repairs

* checking your rate won’t affect your credit score

Get ahead of my car maintenance

* checking your rate won’t affect your credit score

2010 Honda Civic engine oil capacity

For the 2010 Honda Civic DX, Canadian DX-G, LX, EX, and EX-L models, the oil capacity is 3.9 quarts. The Si model has a oil capacity of 4.6 quarts.

The 2010 Civic’s standard models have a 1.8-liter four-cylinder engine with 140 horsepower. There’s also the

trim, which has a similar engine that runs on compressed natural gas.

The hybrid comes with a 1.3-liter I-4gas-electric hybrid propulsion system, while the

Si’s

sport-tuned 2.0-liter turbocharged four-cylinder sacrifices some fuel efficiency to achieve 197 horsepower.

MORE: How much should an oil change cost?

What kind of oil does a 2010 Honda Civic need?

The type of oil you use will also depend on the size of the engine you have in your 2010 Honda Civic. Honda has its own premium-grade motor oil brand that it recommends, but any synthetic oil should do the trick.

Here are the different types of oil you need depending on your 2010 Civic’s model:

DX, Canadian DX-G, LX, EX, and EX-L: 5W-20

Si: 5W-30

Curious how oil types get their names? It has to do with viscosity ratings. A 0W-20 oil has a viscosity—a fancy word for thickness—rating of 0 at 0 degrees Fahrenheit (the “W” stands for “winter”). On the other end of the spectrum, it has a viscosity of 20 at 212 degrees Fahrenheit.

If you’re not sure where to start, Honda's owners manual recommends using 5W-20 Genuine Honda Motor Oil.

MORE:

Ultimate FRAM oil filter guide

How often to change the oil on a 2010 Honda Civic

Since you’re using synthetic oil, your Civic will have a longer-than-average oil life, so don’t go changing your oil before you need to!

A 2010 Honda Civic’s engine oil should be changed about every 7,500 miles driven. Regardless, it’s a good idea to check your oil at least once a month to ensure that it’s still in good condition.

Here are some symptoms to look out for that may indicate your oil is past due for changing:

Dark brown/black oil that looks like thick cola

Gritty, coarse, or dirty oil

Unfamiliar engine noises and smells

Noticeably reduced engine performance

MORE:

What you should know about the Honda Civic battery draining problem

How to change your oil and oil filter

If it turns out that you definitely need to give your 2010 Honda Civic an oil change, you’re going to want to get the following

essential car tools and supplies

ready:

Socket wrench

Drain pan

Filter wrench

Replacement oil filter

4–5 quarts of engine oil

Rags (things could get messy)

First off, let your engine run for a few minutes to warm up the oil, and then turn your car off. After that, follow these steps:

Open the oil fill cap under the hood

Get underneath your engine, at least enough that you can reach its oil drain

Position the drain pan under the oil drain, preparing for the oil to flow out

Remove the oil drain bolt and washer, and the oil will start flowing right away

As the flow starts to slow down, you’re ready to remove the old oil filter

Install the fresh filter, following any instructions included

When the drainage is complete, put the oil drain bolt back on with a new washer, tightening it to 29 lb-ft

Fill your engine with the new oil via the oil fill opening under the hood

After changing your oil, it’s a good idea to turn on your car and let your engine run for about 30 seconds before you check the oil level. This will give you a more accurate measurement, and you’ll be able to top it off if necessary.

Now just close up that oil cap again, and find some containers with lids to store the old oil in for recycling. Lastly, check your oil level to ensure you haven’t underfilled or overfilled your engine!

Don’t forget regular insurance policy maintenance

Doing your own oil change is a great way to save some time and money. You won’t have to wait in line, and you won’t have to pay labor costs.

But we’re willing to bet you’d be interested in even bigger savings than the ones you gain by changing your own oil.

Jerry

is the #1-rated car insurance shopping app and the place to find those savings!

By downloading Jerry for free, you’ll gain access to the cheapest insurance quotes on the coverage you need, sourced from over 55 top insurers. Plus, renewing your insurance or switching to a new plan with Jerry's

trustworthy super app

takes just a few clicks!

The result is an average annual savings of $800+ on your car insurance premium!