Melanie Reiff
Updated on Aug 11, 2022
A mechanic can replace your tie rod ends, which help keep your wheels aligned and ensure proper steering if they become worn or damaged. You’ll need to replace your tie rod ends if your vehicle starts to wander instead of driving straight, or if you notice binding in the steering wheel when turning.
Properly functioning tie rod ends are integral to accurate steering and help keep you safe while driving. That’s why the licensed car insurance super app Jerry has put together everything you need to know about getting your tie rod ends replaced.
The exact cost varies between different Volvo models. For example, newer vehicle models are usually made with more expensive materials, so recent or high-end models will cost more, especially if your service requires a part replacement. Use the table below to estimate the cost for your own vehicle.
CarTotal Cost EstimateParts CostLabor CostAverage Dealer PriceEstimated Service Duration
V90 Cross Country

What is a tie rod end replacement?

For this service, a mechanic will inspect your tie rods to determine whether the rod ends are at fault, and replace them if necessary.
Tie rod ends are connected between the track rod of your car’s steering assembly and the steering knuckle, serving to help accommodate movement of the wheels when steering or driving over irregular terrain.
Most cars have four tie rod ends total, sporting two per side: an outer tie rod end and an inner tie rod end. These are adjustable components whose positioning is crucial for proper wheel alignment and steering.

How to replace a tie rod end

A tie rod end replacement may take a while. Here are the steps a mechanic will go through in the process:
  • Raise and support the vehicle on steel safety stands.
  • Remove the tire and wheel assembly.
  • Measure and record the length of the existing tie rod (if possible). This helps in the alignment process later on.
  • Loosen the tie rod end adjusting lock nut.
  • Use a tie rod end removal tool to separate the tie rod ball stud from the steering knuckle.
  • Unthread the tie rod from the inner tie rod end.
  • Install the new tie rod ends with all fasteners and the adjusting lock nut tightened to the appropriate OEM torque value (this is where the recorded length of the old tie rod is used).
Unless your mechanic has portable equipment, you will have to finish the process by taking your car to an alignment shop, where they will measure and adjust the vehicle’s alignment as needed.

How do I know if my tie rod end needs to be replaced?

You will know your tie rod ends need to be replaced if you notice any (or all) of the following:
  • Clunking noises and a lack of smooth steering. If your steering wheel binds when turning it or if the suspension makes noise during turns, your tie rod ends may be at fault.
  • Vehicle pulling, wandering, or prematurely worn tires. If the tie rod ends have loosened, your car will have difficulty tracking straight ahead, and may “pull” to the left or right. Excessive wear on the front tires is another indicator of this.
  • Obvious looseness in any of the tie rod end components. If the ball stud portion of the tie rod end has any discernible “play” or movement, the entire tie rod end will need to be replaced.
  • A leaking, damaged, or missing rubber boot or bellows. The grease in your outer tie rod ends is contained by a rubber seal. If it fails, grease can leak out and the joint will accumulate and be worn down by road dirt. Inner tie rod ends are protected by bellows. If one of these tears, only it needs to be replaced.

How important is it that I replace the tie rod end?

Incredibly important. You should not drive with a tie rod end problem, as they are a critical component of the steering system. Continued use of a defective tie rod end could result in the breakage of the tie rod itself, which can result in the total loss of steering control—putting you and other drivers at high risk of injury or death. Regular inspection of tie rod ends is necessary to ensure they are in good condition.

How to save on car insurance

Following a regular maintenance schedule is a good idea for every car owner, but so is keeping your car protected with the right car insurance policy.
Licensed car insurance super app Jerry makes shopping for affordable car insurance a breeze and saves the average user $887 a year!
All you have to do is answer a 45-second questionnaire, and Jerry will find your current insurance policy and give you dozens of competitive quotes to compare. When you fall in love with a new low rate, Jerry will even help you cancel your existing policy and switch over!
Keep in mind that your location is another factor that determines the final cost of repairs. Areas with higher cost of living will usually have more expensive car repair services, especially if there’s less local competition. Check out the table below for an estimate of what Volvo drivers pay in different cities.
CityCarTotal Cost EstimateParts CostLabor CostAverage Dealer PriceEstimated Service Duration
V60 Cross Country
S60 Cross Country
V90 Cross Country
Jerry doesn’t just offer fair price repair estimates for Volvo drivers! Our team of writers has collected everything you need to know for every car. Here’s how much the repair costs for some popular cars:
CarTotal Cost EstimateParts CostLabor CostAverage Dealer PriceEstimated Service Duration
2500 Series
K20 Suburban
The cost of repairs might vary depending on which Volvo you drive, but there’s an easy way to save money for the services you need! Just download the Jerry app for help lowering your insurance premiums. In less than 45 seconds, Jerry collects all of your information from your existing insurer. Choose from competitive quotes from top insurance companies and Jerry takes care of the rest—securing your new policy and helping you cancel your old one upon request.
With an average annual savings of $887, Jerry can help you free up funds for the repairs your Volvo’s needs.